bonjour
sur un portable toshiba satellite pro L10 avec Zorin
le wifi fonctionnait hier, aujourd'hui non
la diode ne s'allume plus, les touches Fn + F8 sont inactives
rien en ce qui concerne le wireless dans le bios, qui semble être très basique
dmesg |grep ipw
nadine@nadine-Satellite-PRO-L10:~$ dmesg |grep ipw
[ 22.791198] libipw: 802.11 data/management/control stack, git-1.1.13
[ 22.791202] libipw: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 23.000215] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[ 23.000221] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 23.000361] ipw2200 0000:02:04.0: found PCI INT A -> IRQ 10
[ 23.000380] ipw2200 0000:02:04.0: sharing IRQ 10 with 0000:00:1f.3
[ 23.000385] ipw2200 0000:02:04.0: sharing IRQ 10 with 0000:00:1f.5
[ 23.000390] ipw2200 0000:02:04.0: sharing IRQ 10 with 0000:00:1f.6
[ 23.000423] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 23.844254] ipw2200: Radio Frequency Kill Switch is On:
[ 24.136234] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
[ 48.566058] ipw2200: Failed to send POWER_MODE: Command timed out.
= [ 48.566058] ipw2200: Failed to send POWER_MODE: Command timed out
rfkill list
adine@nadine-Satellite-PRO-L10:~$ rfkill list
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: yes
la commande rfkill unblock all ne change rien
lshw -C network
root@nadine-Satellite-PRO-L10:~# lshw -C network
*-network:0
description: Ethernet interface
produit: RTL-8100/8101L/8139 PCI Fast Ethernet Adapter
fabriquant: Realtek Semiconductor Co., Ltd.
identifiant matériel: 2
information bus: pci@0000:02:02.0
nom logique: eth0
version: 10
numéro de série: 00:c0:9f:b3:66:bd
taille: 100Mbit/s
capacité: 100Mbit/s
bits: 32 bits
horloge: 33MHz
fonctionnalités: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=full ip=192.168.1.36 latency=64 link=yes maxlatency=64 mingnt=32 multicast=yes port=MII speed=100Mbit/s
ressources: irq:6 portE/S:3800(taille=256) mémoire:e0402000-e04020ff
*-network:1 DÉSACTIVÉ
description: Interface réseau sans fil
produit: PRO/Wireless 2200BG [Calexico2] Network Connection
fabriquant: Intel Corporation
identifiant matériel: 4
information bus: pci@0000:02:04.0
nom logique: eth1
version: 05
numéro de série: 00:13:ce:28:89:d2
bits: 32 bits
horloge: 33MHz
fonctionnalités: pm bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=ipw2200 driverversion=1.2.2kmprq firmware=ABG:9.0.5.27 (Dec 12 2007) latency=64 link=no maxlatency=24 mingnt=3 multicast=yes wireless=IEEE 802.11bg
ressources: irq:10 mémoire:e0401000-e0401fff
network:1 DÉSACTIVÉ
description: Interface réseau sans fil
produit: PRO/Wireless 2200BG [Calexico2] Network Connection
si je comprends, c'est à cause du bouton pour activer le wifi puisque la carte intégrée est reconnue
j'ai démonter entierement le portable pour vérifier si rien n'était débranché, rien
et hier, la diode était allumé avec wifi ok
il ne faut pas un firmware pour que certaines touches soit reconnu ?